What is the printer’s speed?
:Answer: *The printing speed varies depending on the used colors of ink and the profile. *The following information is provided only for a guide and is not guaranteed. [UJF-3042 / UJF-3042FX] [UJF-3042HG]
Search Results for: ujf
Which inks can be used?
Answer: The following ink/ink sets are available for each model. 220ml ink cartridges or 600ml eco-cartridges are available. Ink colors are indicated as shown below. [For UJF-3042] For UJF-3042, the LH-100 ink is available. [For UJF-3042FX] For UJF-3042FX, The LH-100 ink, LF-200 ink, LF-140 ink and IJ primer [PR-100] are available. [For UJF-3042HG] For UJF-3042HG, […]
What should i do when [Error201 COMMAND] is displayed?
This error is displayed if data other than command data is received. 1. Reprint with different color profiles. 2. Check if there are some damages on the USB cable. [For UJF-3042HG] Check that the accompanying ferrite core is attached to the USB. If not, attach it. 3. Replace the USB cable to other one. ・Use […]
What should i do when [ERROR505 !WORK High] is displayed?
Answer: This error is displayed when the obstacle sensor detects an obstacle that can collide with the head. Check that the setting value of “MEDIA THICKNESS” or “HEAD GAP” is appropriate against the actual thickness of the media. In addition, check on the followings. ・Dust or garbage is not sticking to the surface of table […]
What should i do when [Error511 Z origin detect] is displayed?
Answer: This error occurs when the table does not operate normally. 1. Make sure the table is moving up & down. 2. Check if there is strange noise around the table. 3. The weight of media must be 5kg or less (including jig) by specifications. Check that the weight of the media mounted on the […]
The display will be Local after each print, what should i do?
Answer: Please see followings. 1. After completing printing, you can set whether to return to Local mode or to remain in Remote mode. For how to set it, see “OPERATION MANUAL” -> “Chapter 3” -> “Various settings” -> “Setting the work change”. When [OFF] is set: Keeps Remote mode after printing. […]
How can the head gap be adjusted?
Answer: Put in the value directly. * Recommended gap is 1.5mm (.015 inch). ・If the head gap is changed, table height is also changed. ・UJF-3042 is equipped with a function [GAP CHECK]. When ON is selected: If an obstacle is detected before or during drawing, the table automatically moves down away from the obstacle. * […]
Can thin substrates be used?
Answer: It can be used by the following products: [For UJF-3042 / UJF-3042FX] Note that, when using thin substrates (such as paper or film), the marks of vacuum holes on the board surface may remain after printing. Be sure to perform a prior test on substrates before using it. [For UJF-3042HG] When you print on […]
What is the power consumption?
Answer: The following data is the power consumption of UJF-3042 series: [For UJF-3042/UJF-3042FX] Operation… 350VA or lower Standby… 120VA or lower [For UJF-3042HG] Operation… 450VA or lower Standby… 125VA or lower
What is the height clearance of the print heads?
Answer: please see the followings [For UJF-3042 / UJF-3042FX] 50mm (1.97″) clearance is supported. [For UJF-3042HG] Up to 150mm (5.9”) is supported. * When printing on a molding object of 100mm or smaller, it is necessary to install the accompanying vacuum table and the table spacers.
